HURTIG LEVERING

LEVERING 1-3 DAGE.

ALTID NYE pRODUKTER !

Vi levere altid enheder med den sidste nye Firmware/Software.

Aldrig gamle vare på lager.

BRUG FOR HJÆLP ? VI GIVER GRATIS RÅDGIVNING

Mads Lund  Tlf. +4520275925

Poul Sørensen Tlf. +4523432758

kontakt@youcontrol.dk

Youcontrol.dk
Besøgende online :27
Livolo switch
6 port powernode
Presence recognition in Fibaro Home Center via Mother Sense Cookie
How to make FIBARO Home Center 2 Gateway
Fibaro RGBW in a pendent light or the Wofi LED Ring for modern living
Using Z-Weather in the Fibaro HomeCenter 2
FIBARO: Heating off when window open – How to save real cash
Easy LUA scripts part 3: How to change the FIBARO Wallplug´s color
netatmo welcome – read the presence-status with the Fibaro HomeCenter 2
This is how you set up the Fibaro Video-Gate as Door intercom #Tutorial
Fibaro Shortcuts: This is how your underfloor heating is going to be smart as well!
This is how you set up a heating schedule in the Fibaro Home Center
To check the Fibaro Presence via iPhone, Smartphone or TV
Sådan at aktivere din alarm med RFID-tag-læser
How to customize your FIBARO app?
FIBARO mobile app How to install the widgets
Fibaro & HomeKit - SmartHome stemmestyring med Siri nemt!
Sådan sender du SMS med Fibaro Home Center
IFFTT Fibaro
Filling the Weather Display of the HomeCenter 2 with your own Values
Using Z-Weather in the Zipabox
https://www.siio.de/sicherheitalarm/netatmo-welcome-kamerabild-im-fibaro-hc-anzeigen/
atom homey
Siio
Facebook
Powered by Magento extensions
YouTube
Powered by Magento extensions

Z-wave Plus - GEN5 Fibaro KeyFob Remote control FIBEFGKF-601

Vær den første til at bedømme dette produkt

Lagerstatus: På lager/fjernlager = 100 vare(r)

Pris: 449,00 DKK

Specialpris Ekskl. moms: 319,20 DKK Inkl. moms: 399,00 DKK

Hurtigt overblik

Z-wave Plus - GEN5 Fibaro KeyFob Remote control FIBEFGKF-601

Z-wave Plus - GEN5 Fibaro KeyFob Remote control FIBEFGKF-601

Flere visninger

Dokumentation : Klik Her  

 

Opsætning med Fibaro 

 

Præsentationsvideo 

Only ONE remote control for ALL!  
     
  Dear Mads Lund,

FIBARO KeyFob  The intelligent remote control for your home

Eventually only ONE remote control for the whole home!

The FIBARO KeyFob allows you to control devices connected within the working range of the Z-Wave network. 
Control the lights, turn on the music, manage temperature, close
the blinds and gates and open the door. Run virtually any devices and scenes you desire. You don't need anymore separate remote controls for every single device lying anywhere but never there where you need it.
 
     
     
 
     
 
 
     
 
The portable KeyFob ensures comfortable and complete home control. Its 6 advantageously placed buttons permit a KeyFob user to either activate pre-programmed scenes or control other devices. KeyFob's powerful functionality is possible due to its communication with  Z-Wave PLUS and the built-in series of Z-Wave GEN5 modules. Compared to the standard Z-Wave protocol, the new Z-Wave PLUS offers an increased network range by 50%, which grants overall faster operation of all connected devices.
 
 
     
  The conveniently compact KeyFob remote with its ideal and modern design comes with a LED RGB, which indicates the current status of the device, like alerting whether it has entered wake up mode, is undergoing a prolonged activation of a particular scene, or if it has a low battery. A KeyFob user can also program a battery alert. If the KeyFob's battery is on low charge you will receive an alert message. When using KeyFob normally, which means about an average of 5 scene activations per day, the battery will last for about 2 years.

Furthermore the FIBARO KeyFob is small enough that you can add it to your key ring and keep your personal controller with you wherever you go.

          FIBARO KEYFOB
                         Your p
ersonal Smart Home Controller 
                                                                            Made just for you
 

 

 

 

 

KeyFob can effortlessly open the garage, light up the driveway for your safety and comfort, and disarm the alarm in your home.

FIBARO KeyFob is a Z-Wave Plus compatible, battery-powered, compact remote control.
Six buttons allow you to control other devices through the Z-Wave network and run various scenes defined in FIBARO System. 
Configure actions for one, two, three clicks and holding the button to suit all your needs.
Built-in locking system will ensure that unauthorized person will not take control of your home.


Main features:

  • Compatible with any Z-Wave or Z-Wave+ Controller,
  • Supports protected mode (Z-Wave network security mode) with AES-128 encryption,
  • Completely wireless and battery powered,
  • Pocket size,
  • Equipped with 6 easily recognizable buttons,
  • 24 different actions: single/double/triple click and hold for each button,
  • Easy to operate menu,
  • Actions confirmed by the built-in LED diode.

technical Details:

Battery type: CR2450 3.0V battery (included)
Battery life: est. 2 years (with default settings and max. 5 pushes per day)
Operating temperature: 0 - 40°C
Radio protocol: Z-Wave (500 series chip)

Range:

  • up to 50m outdoors
  • up to 40m indoors

(Depending on terrain and building structure)

 

 

 

 Technical data

Power supply: CR2450 3.0V battery (included)
Battery life: est. 2 years (default settings, max. 5 pushes per day and direct range)
Operating temperature: 10 – 40°C
EU standards compliance: R&TTE 1999/5/EC
RoHS 2011/65/EU
Radio protocol: Z-Wave (500 series chip)
Radio frequency: 868.4, 868.42 or 869.8 MHz EU;
908.4, 908.42 or 916.0 MHz US;
921.4, 921.42 or 919.8 MHz ANZ;
869.0 or 869.02 MHz RU;
Range: up to 50m (164 ft) outdoors
up to 40m (131 ft) indoors
(Depending on terrain and building structure)
Dimensions: 70 x 38 x 15 mm

 

Using batteries other than specified may result in explosion. Dispose of properly, observing environmental protection rules.

Radio frequency of individual device must be same as your Z-Wave controller. Check information on the box or consult your dealer if you are not sure.

Battery life depends on frequency of usage, number of associations/scenes, Z-Wave routing and network load.

 

Installation

 Basic Activation

  1. Using included keyring or a coin, open the battery cover by turning it counter-clockwise.
  2. Remove the paper strip underneath the battery.
  3. Using included keyring or a coin, close the battery cover by turning it clockwise.
  4. Locate the device nearby the main Z-Wave controller.
  5. Set the main Z-Wave controller in (security/non-security) add mode (see the controller’s manual).
  6. Click any button three times.
  7. LED will pulse white during the adding process.
  8. Wait for the device to be added into the system.
  9. Successful adding will be confirmed by the Z-Wave controller’s message and green LED colour.

 

Z-Wave network

 Adding to the network

Adding (Inclusion) – Z-Wave device learning mode, allowing to add the device to existing Z-Wave network.

To add the device to the Z-Wave network:

  1. Set the main Z-Wave controller in (security/non-security) add mode (see the controller’s manual).
  2. Power the device (insert the battery).
  3. Click any button three times.
  4. LED will pulse white during the adding process.
  5. Wait for the adding process to end.
  6. Successful adding will be confirmed by the Z-Wave controller’s message and green LED colour.

 

Adding in security mode must be performed up to 2 meters from the controller.

In case the device is not added, repeat the adding procedure.

 

 

 Removing from the network

Removing (Exclusion) – Z-Wave device learning mode, allowing to remove the device from existing Z-Wave network.

Removing the device from the Z-Wave network restores all the default parameters of the device.

To remove the device from the Z-Wave network:

  1. Set the main Z-Wave controller in remove mode (see the controller’s manual).
  2. Click circle and minus simultaneously.
  3. Click triangle or cross until LED glows green.
  4. Click plus.
  5. Wait for the removing process to end.
  6. Successful removing will be confirmed by the Z-Wave controller’s message.

 

Operating the device

 Visual indications

The KeyFob is equipped with a LED diode, signalling pushing the buttons, sequences, menu position and status of the device.

Indications for scenes and associations:
After pressing one of the buttons or using sequence, KeyFob indicates status of action with the LED diode.

What you seeWhat it means
Green blink Receiving command confirmed by the controller and associated devices
Yellow blink every 1s Sending commands in progress
Red blink Receiving at least one command was not confirmed by the controller or associated devices

 

Indications for sequences:

What you seeWhat it means
Blue pulse Entering sequence
3 blue pulses Sequence valid
3 red pulses Sequence not valid

 

Device status indications:

What you seeWhat it meansWhat to do
Learning mode
Red blink Device not added Click any button three times to start adding
Fast white pulsing Device in adding mode Wait for adding process to end
Green blink Device added
Lock Mode
Red blink Device locked Unlock using sequence
3 red pulses Wrong sequence Try unlocking again
Red to green transition Device unlocked Press buttons to activate scenes/associations
Green to red transition Device locked using button hold
Battery
3 magenta pulses Low battery Replace the battery
Configuration
2 white pulses Device woken up

 

 Menu

Menu allows to perform Z-Wave network actions. In order to use the menu:

  1. Click circle and minus simultaneously.
  2. Click triangle or cross until LED indicates desired menu position with colour:
    • WHITE – wake up the device
    • GREEN – learning mode (adding/removing)
    • VIOLET –  check battery level
    • YELLOW – reset the device
  3. Click plus to confirm selection, click minus to exit the menu.
  4. LED will pulse twice with same colour as selected menu position to confirm completing action.

Resetting the device from the menu is not available in Lock Mode.

 Back To Top

 Waking up the device

The KeyFob needs to be woken up to receive information about the new configuration from the Z-Wave controller, like parameters and associations.

Use 1st menu position (white) or click circle and plus simultaneously to wake up the device.

 

 Reset

Reset procedure allows to restore the device back to its factory settings, which means all information about the Z-Wave controller and user configuration will be deleted. There are two ways of resetting the device:

Resetting the device using the menu:

  1. Click circle and minus simultaneously.
  2. Click triangle or cross until LED glows yellow.
  3. Click plus.

Emergency resetting the device on start-up:

  1. Remove the battery.
  2. Hold circle and plus, while inserting the battery.

Successful resetting will be confirmed by smoothly brightening and dimming of the yellow LED colour.

Resetting the device is not the recommended way of removing the device from the Z-Wave network. Use the reset procedure only if the primary controller is missing or inoperable. Certain device removal can be achieved by the procedure of removing.

 

 Battery

The KeyFob can be powered with CR2450 (included) battery. Estimated battery life with device added once, default settings, direct range and maximum 5 pushes per day is 2 years.

 

Using batteries other than specified may result in explosion. Dispose of properly, observing environmental protection rules.
Battery life depends on frequency of usage, number of associations/scenes, Z-Wave routing and network load.

 

Checking battery level:

KeyFob automatically warns about low battery with 3 yellow blinks, when battery level is below value selected in parameter 3.

  1. Click circle and minus simultaneously.
  2. Click triangle or cross until LED glows cyan.
  3. Click cross.
  4. LED indicates battery level with a smoothly transitioning colours, where:
    • Green – 100%
    • Yellow – 50%
    • Red – 1%
  5. Wait 2 second or click any button to exit.

Replacing the battery:

  1. Using included keyring or a coin, open the battery cover by turning it counter-clockwise.
  2. Replace the battery.
  3. Using included keyring or a coin, close the battery cover by turning it clockwise.

 

Additional features

 Lock mode

The KeyFob can be protected with a sequence of 2 to 5 button clicks.
When unlocking sequence is set, the device will lock itself after:

  • being inactive for time set in parameter 2 (60 seconds by default),
  • pressing and holding selected button (if set in parameter 2).

To enable Lock Mode:

  • set sequence in parameter 1,
  • set time and/or locking button in parameter 2 (60 seconds by default),
  • set PROTECTION Command Class to Local Protection by Sequence (done automatically by Home Center controller).

Lock Mode will be disabled when:

  • parameter 1 and/or parameter 2 is set to 0,
  • PROTECTION Command Class is set to Unprotected.

When device is locked:

  • pushing buttons will not activate any actions,
  • menu is available, but without option of resetting the device.

Setting the unlocking sequence and locking time-out using Home Center configuration interface:

  1. Go to the device options by clicking the wrench icon.
  2. Select the „Advanced” tab.
  3. Click the “Configure” button in “Lock Mode” section.
  4. Select sequence of 2 to 5 buttons, click “Next”.
  5. Select time to lock and locking button, click “Next”.
  6. Click circle and plus simultaneously to wake up the device.
  7. Wait for the device to configure.

Setting the unlocking sequence using advanced parameter:

Value of parameter = Value of first button + 8 * Value of second button + 64 * Value of third button + 512 * Value of fourth button + 4096 * Value of fifth button

Button square circle cross triangle minus plus
Value 1 2 3 4 5 6
  1. Calculate value of parameter using table and formula above.
  2. Change the value of parameter 1 [2 bytes] to calculated value.
  3. Click circle and plus simultaneously to wake up the device.
  4. Wait for the device to configure.

Setting time to lock and locking button using advanced parameter:

 

Value of parameter = Time to lock in seconds + 256 * Value of locking button
Time to lock should be 0 or 5-255 (seconds)

Button square circle cross triangle minus plus
Value 1 2 3 4 5 6
  1. Calculate value of parameter using table and formula above.
  2. Change the value of parameter 2 [2 bytes] to calculated value.
  3. Click circle and plus simultaneously to wake up the device.
  4. Wait for the device to configure.

You can also use calculator below to calculate value of the parameter:

 

 Sequences

User can create sequences of two to five button to expand number of possible actions. Every sequence sends corresponding Scene ID to the Z-Wave controller with attribute “Key pressed 1 time” (see “Scene activation” on page 11).

Sequences are saved in advanced parameters (no. 3-8).

Activating sequence introduces delay in single, double and tripple click actions for first button in the sequence.

Rules of creating sequences:

  1. Maximum of six sequences can be created.
  2. Each sequence must be unique.
  3. Sequence can consist of two to five button pushes.
  4. Sequence can contain multiple clicks of the same button.

Setting a new sequence using Home Center configuration interface:

  1. Go to the device options by clicking the wrench icon.
  2. Clicking “Add a new sequence”.
  3. Select sequence of 2 to 5 buttons.
  4. Select reaction to sequence.
  5. Save configuration.
  6. Click circle and plus simultaneously to wake up the device.
  7. Wait for the device to configure.

Setting a new sequence using advanced parameter:  

Value of parameter = Value of first button + 8 * Value of second button + 64 * Value of third button + 512 * Value of fourth button + 4096 * Value of fifth button

Button square circle cross triangle minus plus
Value 1 2 3 4 5 6
  1. Calculate value of parameter using table and formula above.
  2. Change the value of corresponding parameter [2 bytes] (parameters 3 to 8 for slots 1 to 6).
  3. Click circle and plus simultaneously to wake up the device.
  4. Wait for the device to configure.

 

 Scene activation

The KeyFob can activate scenes in the Z-Wave controller by sending scene ID and attribute of a specific action.

By default scenes are activated after single clicking or pressing and holding any of the buttons and sequences. Other actions can be activated in parameters 21-26.

Activating a double click will introduce delay to a single click reaction and activating a triple click will introduce delay to a double click reaction.

Scene IDs of buttons:  

Button square circle cross triangle minus plus
Scene ID 1 2 3 4 5 6


Scene IDs of sequences:  

Sequence number  1 2 3 4 5 6
Scene ID 7 8 9 10 11 12


Attributes of actions:

ActionAttribute
Button clicked once Key Pressed 1 time
Button clicked twice Key Pressed 2 times
Button clicked thrice Key Pressed 3 times
Button held Key Held Down
Button released Key Released
Sequence performed Key Pressed 1 time

 

Configuration

 Associations

Association (linking devices) – direct control of other devices within the Z-Wave system network e.g. Dimmer, Relay Switch, Wall Plug, Roller Shutter or scene (may be controlled only through a Z-Wave controller).

Association ensures direct transfer of control commands between devices, is performed without participation of the main controller and requires associated device to be in the direct range.

States of the association groups are affected only by buttons. Changing state of associated device by other means will not update remembered state of association group.

2, 4, 6, 8, 10 and 12 association groups use BASIC CC, but device does not repond to GET commands.

 

The KeyFob provides the association of four groups:

1st association group – “Lifeline” reports the device status and allows for assigning single device only (main controller by default).
2nd association group – “Square – On/Off” is assigned to clicking the square button and is used to turn on/off associated devices.
3rd association group – “Square – Multilevel” is assigned to clicking and holding the square button and is used to turn on/off and change level of associated devices.
4th association group – “Circle – On/Off” is assigned to clicking the circle button and is used to turn on/off associated devices.
5th association group – “Circle – Multilevel” is assigned to clicking and holding the circle button and is used to turn on/off and change level of associated devices.
6th association group – “Cross – On/Off” is assigned to clicking the cross button and is used to turn on/off associated devices.
7th association group – “Cross – Multilevel” is assigned to clicking and holding the cross button and is used to turn on/off and change level of associated devices.
8th association group – “Triangle – On/Off” is assigned to clicking the triangle button and is used to turn on/off associated devices.
9th association group – “Triangle – Multilevel” is assigned to clicking and holding the triangle button and is used to turn on/off and change level of associated devices.
10th association group – “Minus – On/Off” is assigned to clicking the minus button and is used to turn on/off associated devices.
11th association group – “Minus – Multilevel” is assigned to clicking and holding the minus button and is used to turn on/off and change level of associated devices.
12th association group – “Plus – On/Off” is assigned to clicking the plus button and is used to turn on/off associated devices.
13th association group – “Plus – Multilevel” is assigned to clicking and holding the plus button and is used to turn on/off and change level of associated devices.

 

The KeyFob in 2nd to 13th group allows to control 5 devices (regular or multichannel) per an association group.
“LifeLine” group is reserved solely for the controller and hence only 1 node can be assigned.

It is not recommended to associate more than 10 devices in general, as the response time to control commands depends on the number of associated devices. In extreme cases, system response may be delayed.

 

To add an association (using the Home Center controller):

  1. Go to the device options by clicking the wrench icon.
  2. Select the „Advanced” tab.
  3. Click the “Setting Association” button.
  4. Specify to which group and what devices are to be associated.
  5. Save the changes.
  6. Click circle and plus simultaneously to wake up the device.

Paired buttons associations

After pairing buttons, horizontal pairs of buttons (square and circlecross and triangleminus and plus) work as one button and send associations to left buttons groups only.

Left buttons (squarecrossminus) turn on associated devices and right buttons (circletriangleplus) turn them off.

In multilevel association groups (3, 7, 11) left buttons increase level while holding and right buttons decrease it.

To pair buttons:

  1. Change settings of parameters:
    • square and circle – set parameter 6 to value 1
    • cross and triangle – set parameter 7 to value 1
    • minus and plus – set parameter 8 to value 1
  2. Save the changes.
  3. Click circle and plus simultaneously to wake up the device.
Producent Fibaro
Dimensioner 70 x 38 x 15 mm
Vægt 0.2000
Forsyningsspænding 3.0V Batteri CR2450 (inkluderet)
Radiofrekvens 868,42 MHz
Radio-protokol: Z-Wave Plua
Dokumentation

Dokumentation : Klik Her 

Rækkevidde Udendørs ca 50meter, indendørs op til 30meter

Indsend din bedømmelse

Kun registrerede brugere kan skrive bedømmelser. Log ind eller registrer