Manuals for firmware 3.2:

 Operating manual – English

FIBARO Door/Window Sensor 2 is a wireless, battery powered, Z-Wave Plus compatible magnetic contact sensor. Changing the device’s status will automatically send signal to the Z-Wave controller and associated devices.

Sensor can be used to trigger scenes and wherever there is a need for information about opening or closing of doors, windows, garage doors, etc. Opening is detected by separating the sensor’s body and the magnet.

In addition the FIBARO Door/Window Sensor 2 is equipped with a built-in temperature sensor.

• Compatible with any Z-Wave or Z-Wave+ Controller,
• Supports protected mode (Z-Wave network Security Mode) with AES-128 encryption,
• Works with other Z-Wave network devices, but as a battery device doesn’t take part in signal routing,
• Door/window opening detected through separation of Sensor’s body and a magnet,
• Built-in temperature sensor,
• Detects tampering, when detached or opened,
• Easily mounted on doors, windows, garage gates and roller blinds,
• Battery powered,
• Visual LED indicator signalling status of the device,
• 7 color variations.

1. Take off the cover.
2. Remove the battery blocker.
3. Close the cover.
4. Place the device within the direct range of your Z-Wave controller.
5. Set the main controller in (Security/non-Security Mode) add mode (see the controller’s manual).
6. Quickly, three times press one of the TMP buttons (while the other button is pressed).
7. Install the device on door/window.

To install the Door/Window Sensor 2:

1. Peel off the protective layer from the sticker on the device.
2. Stick the device onto the door/window frame.
3. Peel off the protective layer from the sticker on the magnet.
4. Stick the magnet onto the moving part of the door/window, no further than 5mm from the sensor.

Positioning of the Sensor and the magnet:

Correct positioning of the magnet in relation to the Sensor:
(vertical line marks should align)

Adding (Inclusion) – Z-Wave device learning mode, allowing to add the device to existing Z-Wave network.

To add the device to the Z-Wave network:

1. Place the Door/Window Sensor 2 within the direct range of your Z-Wave controller.
2. Set the main controller in (Security/non-Security Mode) add mode (see the controller’s manual).
3. Quickly, three times press one of the TMP buttons (while the other button is pressed).

1. Wait for the adding process to end.
2. Successful adding will be confirmed by the Z-Wave controller’s message.

Removing (Exclusion) – Z-Wave device learning mode, allowing to remove the device from existing Z-Wave network.

To remove the device from the Z-Wave network:

1. Place the Door/Window Sensor 2 within the direct range of your Z-Wave controller.
2. Set the main controller into remove mode (see the controller’s manual).
3. Quickly, three times press one of the TMP buttons (while the other button is pressed).

1. Wait for the removing process to end.
2. Successful removing will be confirmed by the Z-Wave controller’s message.

The Door/Window Sensor 2 is equipped with a tamper switch with two buttons.

First TMP button is located inside the device, pressed by the closed cover and is used to detect openning it.

Second TMP button is located at bottom of the device, pressed by the surface on which the device is mounted and is used to detect detaching the device.

For the tamper switch to work one of the buttons must always be pressed!

When one of the buttons is released, the tamper alarm will be send to the controller and associated devices.
Additionally, tamper button allows to control the device directly.

Reset procedure allows to restore the device back to its factory settings, which means all information about the Z-Wave controller and user configuration will be deleted.

Resetting the Door/Window Sensor 2:

1. Open the cover.
2. Remove the battery.
3. Install the battery while holding both TMP buttons.
4. Visual LED indicator will be flashing slowly for 5 seconds – keep holding the buttons.
5. Release one button when the LED indicator starts flashing quickly.
6. Click released button once to confirm launching of reset procedure.
7. Wait a few seconds until a long blink of the LED indicator. Do not remove the battery.
8. Visual LED indicator will blink 5 times quickly to confirm the reset.

The Door/Window Sensor 2 needs to be woken up to receive information about the new configuration from the controller, like parameters and associations.

To wake up the sensor manually, click one of the TMP buttons (while the other button is pressed).

After adding the Sensor to the FIBARO System, it will be represented by two or three icons in Home Center interface.

First icon informs about the status of magnetic sensor (open/close), second icon displays temperature measured by the built-in sensor. Third icon is assigned to high/low temperature alarm and is visible only if parameter 54 is not equal to 0.

The device uses Notification Command Class to report different events.

Association (linking devices) – direct control of other devices within the Z-Wave system network e.g. Dimmer, Relay Switch, Wall Plug, Roller Shutter or scene (may be controlled only through a Z-Wave controller).

The Door/Window Sensor 2 provides the association of three groups:

1st association group – “Lifeline” reports the device status and allows for assigning single device only (main controller by default).
2nd association group – “On/Off” is assigned to the device status – contact sensor (sends Basic Set command frames).
3rd association group – “Tamper” is assigned to the TMP switch (sends alarm command frames).

To add an association (using the Home Center controller):

1. Go to device options by clicking the icon: 
2. Select the „Advanced” tab
3. Click the “Setting Association” button.
4. Specify to which group and what devices are to be associated.
5. Save the changes.
6. Wake up the device manually or wait for the next automatic wake up.

The Door/Window Sensor 2 allows to customize its operation to user’s needs. The settings are available in the FIBARO interface as simple options that may be chosen by selecting the appropriate box.
In order to configure the Door/Window Sensor 2 (using the Home Center controller):

1. Go to the device options by clicking the icon: 
2. Select the „Advanced” tab.
3. Modify values of chosen parameters.
4. Save the changes.
5. Wake up the device.

Wake up interval (battery mode)

Available settings: 0 or 3600-64800 (in seconds, 1h – 18h)
Default setting: 21600 (6h)

The Door/Window Sensor 2 will wake up at each defined time interval and always try to connect with the main controller. Longer wake up time interval means less frequent communication and thus a longer battery life.

After successful communication attempt, the device will update configuration parameters, associations and settings and then will go into Z-Wave communication standby.

After failed communication attempt (eg. no Z-Wave range) the device will go into Z-Wave communication standby and retry to establish connection with the main controller after the next time interval.

Setting wake up interval to 0 disables sending Wake Up notification to the controller automatically. Wake up may be still performed manually.