HURTIG LEVERING

LEVERING 1-3 DAGE.

ALTID NYE pRODUKTER !

Vi levere altid enheder med den sidste nye Firmware/Software.

Altid nyeste varer på lager.

BRUG FOR HJÆLP ?

Mads Lund  Tlf. +4520275925

Poul Sørensen Tlf. +4523432758

kontakt@youcontrol.dk

Youcontrol.dk
Besøgende online :51
Livolo switch
6 port powernode
Presence recognition in Fibaro Home Center via Mother Sense Cookie
How to make FIBARO Home Center 2 Gateway
Fibaro RGBW in a pendent light or the Wofi LED Ring for modern living
Using Z-Weather in the Fibaro HomeCenter 2
FIBARO: Heating off when window open – How to save real cash
Easy LUA scripts part 3: How to change the FIBARO Wallplug´s color
netatmo welcome – read the presence-status with the Fibaro HomeCenter 2
This is how you set up the Fibaro Video-Gate as Door intercom #Tutorial
Fibaro Shortcuts: This is how your underfloor heating is going to be smart as well!
This is how you set up a heating schedule in the Fibaro Home Center
To check the Fibaro Presence via iPhone, Smartphone or TV
Sådan at aktivere din alarm med RFID-tag-læser
How to customize your FIBARO app?
FIBARO mobile app How to install the widgets
Fibaro & HomeKit - SmartHome stemmestyring med Siri nemt!
Sådan sender du SMS med Fibaro Home Center
IFFTT Fibaro
Filling the Weather Display of the HomeCenter 2 with your own Values
Using Z-Weather in the Zipabox
https://www.siio.de/sicherheitalarm/netatmo-welcome-kamerabild-im-fibaro-hc-anzeigen/
atom homey
Siio
Facebook
Powered by Magento extensions
YouTube
Powered by Magento extensions

Z-Wave Plus - Fibaro Double Switch 2 ( 2 * 1,15 KW ) FIBEFGS-223

Vær den første til at bedømme dette produkt

Lagerstatus: På lager/fjernlager = 100 vare(r)

Ekskl. moms: 367,20 DKK Inkl. moms: 459,00 DKK

Hurtigt overblik

Z-Wave Plus - Fibaro Double Switch 2 ( 2 * 1,15 KW ) FIBEFGS-223

Z-Wave Plus - Fibaro Double Switch 2  ( 2 * 1,15 KW ) FIBEFGS-223

Flere visninger

Downloads

 Manuals

Manuals for firmware 3.2:

en Operating manual – English

pl Instrukcja obsługi – Polski

 

 Short manual – European Multilanguage

 Short manual – American Multilanguage

 Back To Top

 Declarations

Declarations of conformity:

en FGS-213-EN.pdf

en FGS-223-EN.pdf

pl FGS-213-PL.pdf

pl FGS-223-PL.pdf

 Back To Top

Description and features

 Description

FIBARO Switch 2 is designed to be installed in standard wall switch boxes or anywhere else where it is necessary to control electric devices. FIBARO Switch 2 allows to control connected devices either via the Z-Wave+ network or via a switch connected directly to it and is equipped with active power and energy consumption metering functionality.

FIBARO  Switch 2 comes in two versions:

  • Single Switch 2 (FGS-213) – can control one electric device
  • Double Switch 2 (FGS-223) – can control two electic devices

 Back To Top

 Features

  • Compatible with any Z-Wave or Z-Wave+ Controller
  • Supports protected mode (Z-Wave network security mode) with AES-128 encryption
  • Advanced microprocessor control
  • Active power and energy metering functionality
  • Works with various types of switches – momentary, toggle
  • three-way, etc
  • To be installed in wall switch boxes of dimensions allowing for installation, conforming to provisions of applicable regulations
  • FIBARO Switch 2 is an extension unit

 

This device may be used with all devices certified with the Z-Wave Plus certificate and should be compatible with such devices produced by other manufacturers.

FIBARO Switch2 is a Security Enabled Z-Wave Plus product and a Security Enabled Z-Wave Controller must be used in order to fully utilize the product.

 

 Back To Top

 Supported loads

The Switch 2 may operate under the following loads:
Conventional incandescent light sources,
Halogen light sources,
Electrical appliances which power consumption does not exceed the limit for a specified device.

 

Applied load and the Switch 2 itself may be damaged if the applied load is inconsistent with the technical specifications!

When connecting the Switch 2 act in accordance with the following rules:

  • Do not connect loads greater than those recommended!
  • Do not connect types of load other than resistive or incandescent!

     

Rated load current table:

DeviceLoad type IEC standards UL standards
Single Switch 2
(FGS-213)
 Resistive  8A  6.5A
Single Switch 2
(FGS-213)
 Incandescent  8A  5A
Double Switch 2
(FGS-213)
 Resistive 6.5A per channel
10A overall
6A per channel
9.5A overall
Double Switch 2
(FGS-223)
 Incandescent  6.5A per channel
10A overall
 3A per channel

 

IEC certification applies in EU countries and most countries using 220-240V~. UL certification applies in United States and most countries using 100-120V~.

 Back To Top

 Technical data

Power supply: 100-240V~ 50/60 Hz
Rated load current: Single Switch 2 (FGS-213):
IEC standards: 8A
UL standards (resistive load): 6.5A
UL standards (incandescent load): 5ADouble Switch 2 (FGS-223):
IEC standards: 6.5A per channel, 10A overall
UL standards (resistive loads): 6A per channel, 9.5A overall
UL standards (incandescent loads): 3A per channel
Operating temperature: 0-35°C
For installation in boxes: Ø ≥ 50mm, depth ≥ 60mm
Overcurrent protection: required external 10A circuit breaker
Radio protocol: Z-Wave (500 series chip)
Radio signal power: up to 1mW
Radio frequency: 868.4 or 869.8 MHz EU;
908.4, 908.42 or 916.0 MHz US;
921.4 or 919.8 MHz ANZ;
869.0 MHz RU;
Range: up to 50m outdoors
up to 40m indoors
(depending on terrain and building structure)
Comply with EU directives: R&TTE 1999/5/EC
RoHS 2011/65/EU
Dimensions (L x W x H): 42.5 x 38.25 x 20.3 mm

 

IEC certification applies in EU countries and most countries using 220-240V~. UL certification applies in United States and most countries using 100-120V~.

Radio frequency of individual device must be same as your Z-Wave controller. Check information on the box or consult your dealer if you are not sure.

 

 Back To Top

Installation

 Installation

 

Connecting the device in a manner inconsistent with manual may cause risk to health, life or material damage.

When connecting the device act in accordance with the following rules:

  • Connect only in accordance with one of the diagrams,
  • Electrical installation must be protected by overcurrent protection (fuse) of with a value not higher than 10A,
  • The Switch 2 should be installed in a wall switch box compliant with a relevant national safety standards and with depth no less than 60mm,
  • Electrical switches used in installation should be compliant with the relevant safety standards,
  • Length of wires used to connect the control switch should not exceed 10m.

     

Notes for the diagrams:

  S1 – terminal for 1st switch (has the function of activating the learning mode)
  S2 – terminal for 2nd switch
  L – terminal for live lead
  Q/Q1 – output terminal of the 1st channel
  Q2 – output terminal of the 2nd channel (only Double Switch 2)
  N – terminal for neutral lead
  B – service button (used to add/remove the device and navigate the menu)

Installation of the device:

  1. Switch off the mains voltage (disable the fuse).
  2. Open the wall switch box.
  3. Connect with one of the diagrams below for appropriate device.
  4. After verifying correctness of the connection switch on the mains voltage.
  5. Add the device to the Z-Wave network.
  6. Turn off the mains voltage, then arrange the device and its antenna in a wall switch box.
  7. Close the wall switch box and turn on the mains voltage.

 

Switch connected to the S1 terminal is a master switch. It activates the basic functionality of the device (turning the first load on/off) and activates the learning mode (adding/removing). The switch connected to the S2 terminal turns on/of the second load in Double Switch 2, but is optional in Single Switch 2 and pushing it will not affect the status of the device.

After switching on the mains voltage LED indicator will signal Z-Wave network inclusion state with a colour:
GREEN - device added
RED - device not added

 

Wiring diagrams:

sswitch2_diagrams

Wiring diagrams – Single Switch 2

dswitch2_diagrams

Wiring diagrams – Double Switch 2

 Back To Top

 Video tutorials

FIBARO Single Switch 2 – 3-wire connection with single switch:

 

FIBARO Single Switch 2 – electric socket connection:

 

FIBARO Double Switch 2 – connection with double switch:

 Back To Top

 Arranging the antenna

  • Locate the antenna as far from metal elements as possible (connecting wires, bracket rings, etc.) in order to prevent interferences.
  • Metal surfaces in the direct vicinity of the antenna (e.g. flush mounted metal boxes, metal door frames) may impair signal reception!
  • Do not cut or shorten the antenna – its length is perfectly matched to the band in which the system operates.

 Back To Top

Z-Wave network

 Adding to the network

Adding (Inclusion) – Z-Wave device learning mode, allowing to add the device to existing Z-Wave network.

To add the device to the Z-Wave network:

  1. Place the Switch 2 within the direct range of your Z-Wave controller.
  2. Identify the S1 switch.
  3. Set the main controller in (security/non-security) add mode (see the controller’s manual).
  4. Quickly, three times press the S1 switch.
  5. Wait for the adding process to end.
  6. Successful adding will be confirmed by the Z-Wave controller’s message.

 

In case of problems with adding/removing using S1 switch, use B-button instead (located on the housing)

While adding the Switch 2 to the network with connected toggle switch, ensure that switch contact is open (off). Otherwise it will prevent adding/removing the device to/from the network.

Adding in security mode must be performed up to 2 meters from the controller.

 

 Back To Top

 Removing from the network

Removing (Exclusion) – Z-Wave device learning mode, allowing to remove the device from existing Z-Wave network.

Removing the device from the Z-Wave network restores all the default parameters of the device.

To remove the device from the Z-Wave network:

  1. Place the Switch 2 within the direct range of your Z-Wave controller.
  2. Identify the S1 switch.
  3. Set the main controller in remove mode (see the controller’s manual).
  4. Quickly, three times press the S1 switch.
  5. Wait for the removing process to end.
  6. Successful removing will be confirmed by the Z-Wave controller’s message.

In case of problems with adding/removing using S1 switch, use B-button instead (located on the housing)

 Back To Top

 Range test

The Switch 2 has a built in Z-Wave network main controller’s range tester.

To make Z-Wave range test possible, the device must be added to the Z-Wave controller. Testing may stress the network, so it is recommended to perform the test only in special cases.

Follow the below instructions to test the main controller’s range:

  1. Switch off the mains voltage (disable the fuse).
  2. Remove the Switch 2 from the wall switch box.
  3. Switch on the mains voltage.
  4. Press and hold the B-button to enter the menu.
  5. Wait for the visual LED indicator to glow violet.
  6. Quickly release and click the B-button again.
  7. Visual indicator will indicate the Z-Wave network’s range (range signalling modes described below).
  8. To exit Z-Wave range test, click the B-button.

Z-Wave range tester signalling modes:

  • Visual indicator pulsing green – the Switch 2 attempts to establish a direct communication with the main controller. If a direct communication attempt fails, the device will try to establish a routed communication, through other modules, which will be signalled by visual indicator pulsing yellow.
  • Visual indicator glowing green – the Switch 2 communicates with the main controller directly.
  • Visual indicator pulsing yellow – the Switch 2 tries to establish a routed communication with the main controller through other modules (repeaters).
  • Visual indicator glowing yellow – the Switch 2 communicates with the main controller through the other modules. After 2 seconds the device will retry to establish a direct communication with the main controller, which will be signalled with visual indicator pulsing green.
  • Visual indicator pulsing violet – the Switch 2 does communicate at the maximum distance of the Z-Wave network. If connection proves successful it will be confirmed with a yellow glow. It’s not recommended to use the device at the range limit.
  • Visual indicator glowing red – the Switch 2 is not able to connect to the main controller directly or through another Z-Wave network device (repeater).

Communication mode of the device may switch between direct and one using routing, especially if the device is on the limit of the direct range.

 Back To Top

Operating the device

 Operating using connected switch

Operating the Switch 2 using a momentary switch and parameter 20 set to 0:

  • 1x click:
    Change the state of the connected load to the opposite one (S1 switches 1st channel, S2 switches 2nd channel),
    Change the state of 2nd, 3rd (S1 switch), 4th and 5th (S2 switch) association group to the opposite one.
  • 2x click:
    Set maximum level of devices associated in 2nd, 3rd (S1 switch), 4th and 5th (S2 switch) group.
  • Hold:
    Start smooth control of devices associated in 3rd (S1 switch) and 5th (S2 switch) group.
  • Release:
    Stop smooth control of devices associated in 3rd (S1 switch) and 5th (S2 switch) group.

Operating the Switch 2 using a toggle switch and parameter 20 set to 1:

  • Close switch contact:
    Turn ON the connected load (S1 switches 1st channel, S2 switches 2nd channel),
    Turn ON devices associated in 2nd, 3rd (S1 switch), 4th and 5th (S2 switch) group.
  • Open switch contact:
    Turn OFF the connected load (S1switches 1st channel, S2switches 2nd channel).
    Turn OFF devices associated in 2nd, 3rd (S1 switch), 4th and 5th (S2 switch) group.

Operating the Switch 2 using a toggle switch and parameter 20 set to 2:

  • Change switch position once:
    Change the state of the connected load to the opposite one (S1 switches 1st channel, S2 switches 2nd channel),
    Change the state of 2nd, 3rd (S1 switch), 4th and 5th (S2 switch) association group to the opposite one.
  • Change switch position twice:
    Set maximum level of devices associated in 2nd, 3rd (S1 switch), 4th and 5th (S2 switch) group.

 

Momentary switch:
After releasing the switch a spring automatically pushes back and disconnects the switch)

Toggle switch:
Operates as a two-position switch, it has no spring that would set one position of the switch.

Toggle switch and parameter 20 set to 1:
State of the device is synchronized with state of the external toggle switches.

Toggle switch and parameter 20 set to 2:
State of the device is reversed with every change in state of the external toggle switch.

 

 Back To Top

 Operating using the B-button

The Switch 2 is equipped with a B-button, which allows to use the menu and perform the following actions:

  • 1x click:
    Cancel alarm mode (flashing alarm).
    Select desired menu position (if menu is active).
    Exit range test.
    Turn 1st channel ON/OFF.
  • 3x click:
    Send the Node Info Z-Wave command frame (adding/removing).
  • Hold:
    Enter the menu (confirmed by the LED indicator).

 Back To Top

 Menu

Menu allows to perform Z-Wave network actions. In order to use the menu:

  1. Switch off the mains voltage (disable the fuse).
  2. Remove the Switch 2 from the wall switch box.
  3. Switch on the mains voltage.
  4. Press and hold the B-button to enter the menu.
  5. Wait for the LED to indicate the desired menu position with colour:
    • GREEN – reset energy consumption memory
    • VIOLET – start range test
    • YELLOW – reset the device
  6. Quickly release and click the B-button again.

 Back To Top

 Reset

Reset procedure allows to restore the device back to its factory settings, which means all information about the Z-Wave controller and user configuration will be deleted.

Resetting the device is not the recommended way of removing the device from the Z-Wave network. Use reset procedure only if the primary controller is missing or inoperable. Certain device removal can be achieved by the procedure of removing.

Resetting the device:

 

  1. Switch off the mains voltage (disable the fuse).
  2. Remove the Switch 2 from the wall switch box.
  3. Switch on the mains voltage.
  4. Press and hold the B-button to enter the menu.
  5. Wait for the visual LED indicator to glow yellow.
  6. Quickly release and click the B-button again.
  7. After few seconds the device will be restarted, which is signalled with the red LED indicator colour.

 Back To Top

Additional features

 Power and energy consumption

The Switch 2 allows for the active power and energy consumption monitoring. Data is sent to the main Z-Wave controller, e.g. Home Center.

Measuring is carried out by the most advanced micro-controller technology, assuring maximum accuracy and precision (+/- 1% for loads greater than 5W).

Electric active power – power that energy receiver is changing into a work or a heat. The unit of active power is Watt [W].

Electric energy – energy consumed by a device through a time period. Consumers of electricity in households are billed by suppliers on the basis of active power used in given unit of time. Most commonly measured in kilowatt-hour [kWh]. One kilowatt-hour is equal to one kilowatt of power consumed over period of one hour, 1kWh = 1000Wh.

 

The Switch 2 require the power consumption of connected load equal to 5W or greater to correctly measure the power and energy.

Power measurement can contain mains voltage fluctuations within +/- 10%.

The Switch 2 stores periodically (every hour) the consumption data in the device memory. Disconnecting the module from the power supply will not erase stored energy consumption data.


Resetting consumption memory:
The Switch 2 allows to erase stored consumption data in three ways:

 

  • Using functionality of a Z-Wave controller (see the controller’s manual).
  • Manually clearing the data using the following procedure:
    1. Switch off the mains voltage (disable the fuse).
    2. Remove the Switch 2 from the wall switch box.
    3. Switch on the mains voltage.
    4. Press and hold the B-button to enter the menu.
    5. Wait for the visual LED indicator to glow green.
    6. Quickly release and click the B-button again.
    7. Energy consumption memory will be erased.
  • By resetting the device.

 Back To Top

 Overheat and overcurrent protection

The Switch 2 after detecting overheat or overcurrent will:

  • switch off its relay/relays,
  • send information about switching off the relay/relays to the controller,
  • send Notification Report to the controller (Heat Alarm for overheat, Power Management for overcurrent).

 Back To Top

Configuration

 Associations

Association (linking devices) – direct control of other devices within the Z-Wave system network e.g. Dimmer, Relay Switch, Wall Plug, Roller Shutter

Producent Fibaro
Dimensioner 42.5 x 38.25 x 20.3 mm
Vægt 0.2000
EU regulations EN55022(radiobølge interferens), EN61000-6 (sikkerheden ved brug)
Strømforbrug 230V +/- 10%, 50Hz
Overophedning beskyttelse 105°C
Radiofrekvens 868 MHz
Radio-protokol: Z-Wave
Elforbrug < 0,8W
Dokumentation

Hent Fibaros installations manual ENG klik her.

Arbejds temperatur 10°C - 40°C
Rækkevidde Udendørs ca 50meter, indendørs op til 30meter
Video Se video
Maks Udgangseffekt 2 x 1.15 kW

Indsend din bedømmelse

Kun registrerede brugere kan skrive bedømmelser. Log ind eller registrer