HURTIG LEVERING

LEVERING 1-3 DAGE.

ALTID NYE pRODUKTER !

Vi leverer altid enheder med den sidste nye Firmware/Software.

Altid nyeste varer på lager.

BRUG FOR HJÆLP ?

Mads Lund  Tlf. +4520275925

Poul Sørensen Tlf. +4523432758

[email protected]

Youcontrol.dk
Besøgende online :31
Facebook
Powered by Magento extensions
YouTube
Powered by Magento extensions

Z-Wave Plus - Lysdæmper og bagbelysning MATRIX 55 Til CE standarden ZDB5400 ( Levering 3-4 dage )

Vær den første til at bedømme dette produkt

Lagerstatus: På lager/fjernlager = 82 vare(r)

Ekskl. moms: 959,20 DKK Inkl. moms: 1.199,00 DKK

Hurtigt overblik

Z-Wave Plus - Lysdæmper MATRIX 55 Til CE standarden ZDB5400

Z-Wave Plus - Lysdæmper og bagbelysning MATRIX 55 Til CE standarden ZDB5400 ( Levering 3-4 dage )

Flere visninger

( Levering 3-4 dage )


Virker Med : 

 
 
 

MATRIX 55: Til CE standarden

Med dens indbyggede universelle lysdæmper, bagbelyste tangenter og trådløse Z-Wave kommunikation er MATRIX 55 det logiske valg når du skal vælge betjeningstryk til dit smart home.

Den indbyggede lysdæmper kan kontrollere en lokal belastning, fx et lampeudtag og dermed erstatte en standard et-polet afbryder.

 

 Sofistikeret lysdæmper

Lysdæmperen kan dæmpe alle dæmpbare lyskilder fra 0-250 W. Selv dine energibesparende LEDer.

 

 Forbedrer Z-Wave-netværket

Fungerer som Z-Wave netværks-repeater så netværket forstærkes.

 

 Kompatibilitet

MATRIX 55 basen er konstrueret så den passer i standard CE vægdåser (60 mm). Fronten er designet til at passe i standard 55 mm rammer inklusiv GIRA System 55, Elko Plus og Exxact.

 

  Z-Wave Plus

Baseret på Z-Wave Plus 500 Series platformen.

 

Konstruktion

  1. Basen indeholder al magien og passer i standard CE vægdåser (60 mm).
  2. Valgfri ramme med indre mål på 55×55 mm – ikke inkluderet.
  3. Frontmodulet har LED dioder og metalfjedre som fæstner frontmodulet til basen
  4. Anti-tyveri skruen gør Matrix 55 egnet til offentlige bygninger og virksomheder.
  5. Tangenten er lavet af translucent hvid plast, der matcher dine eksisterende rammer, stikkontakter og afbrydere.

Download “MATRIX 55 ZDB5400 Datablad”matrix-55-datablad.pdf – Downloadet 140 gange – 3 MB

 

 

EAN: 5714090000196

 
Monteringsvejledning
Warning! Only authorised technicians under consideration of the country-specific installation norms may do works with 230 Volt mains power. Prior to the assembly of the product, the voltage network has to be switched off.

 

MATRIX 55 is designed for fitting into standard 60mm CE wall boxes. For compatible design frames, see section about design frames.

For easy installation MATRIX 55 is provided with a connection terminal with push-in terminations. The cable must have a stripped length between 9 and 10 mm. The maximum conductor size is 2.5 mm2, or maximum 1.5 mmfor stranded conductors with a ferrule with plastic collar.

Wiring

Dimmed output (~), Neutral (N) and Line (L) must be connected according to the diagram below. Contacts with same markings (N or L) are internally connected and can be used for cable looping.

Cable connection / Disconnection

When installing a MATRIX 55, simply push solid cables into the connection terminals. Stranded cables must be connected by use of the release-buttons. Activate the release-button on the terminal with a slotted screwdriver with a 2.5 mm slot while pushing in the cable

When removing the cables, use the release-buttons as described above.

Fitting

Fit MATRIX using the elements in the figure below. The safety screw (4) is necessary in public buildings and businesses to avoid theft. Use bullets D) and F)-G) to mount the safety screw.

  1. Mount the Insert (1) in the wall box using the wiring diagram above, regard the UP arrow.
  2. Add the insert to the Z-Wave system, see Chapter 6.
  3. Place the design frame (2) over the insert (1).
  4. (Optional) Remove Pushbutton cover (5) from the front module.
  5. Plug the Pushbutton base (3) into the Insert (1), regard the UP arrow.
  6. (Optional) Fasten the Pushbutton base to the Insert with the Safety screw (4).
  7. (Optional) Snap on the Pushbutton cover (5).
Demounting the Pushbutton Cover when the Safety Screw is mounted

With the safety screw mounted, the pushbutton cover must be removed from the Pushbutton base before unscrewing. Use the following steps.

  1. Loosen the cover with a slotted screwdriver in one side in the slot between the cover and the cover frame;
    • First insert the screwdriver in the right top just below the upper snap (a) and pop out the snap.
    • Afterwards insert the screwdriver in the right bottom just above the lower snap (b). Now release the entire right side.
  2. Hold the right side out from the wall while the left side is released with a single pop somewhere on the left side (c).
  3. Now it is possible to unscrew the safety screw and remove the front module and insert from the wall box.

Adding/Removing

MATRIX 55 is a SmartStart enabled product and can be added into a Z-Wave network by scanning the Z-Wave QR Code present on the product with a controller providing SmartStart inclusion. No further action is required and the SmartStart product will be added automatically within 10 minutes of being switched on in the network vicinity.Find the DSK, QR code and PIN Code on the front of the insert module.

Add MATRIX 55 to a network with Classic Inclusion by pressing once on the switch (I) through the hole with a non-conductive object. The LED inside the module will start blinking.

Use same procedure for removing MATRIX 55 with Classic Exclusion.

If MATRIX 55 already belongs to a Z-Wave network, the remove process must be performed before adding it in a new network. Otherwise, the adding of the device will fail.

 

Restore Factory Settings

Factory settings are restored by pressing the switch through the hole (I) and hold it for min. 10 seconds.

Compatible Design Frames

MATRIX 55 is compatible with a range of design frames from other manufacturers. The design frame must have a 55×55 mm opening and a depth of min.10 mm. This includes, but is not limited to, the following frame systems:

  • Schneider Electric, Exxact
  • Elko Plus
  • GIRA, System 55
  • Merten, System M
  • Busch-Jaeger, Basic 55
Tekniske Data
DIMENSIONER (HXBXD) 70 (55) mm x  70 (mm) mm x 39 (12) mm
STRØMFORSYNING 100 – 240 V AC / 50 Hz
STRØMFORBRUG Maks. 0,8 W / 0,5 W standby
BELASTNING 0-250 W
TERMINALER Skrueløse terminaler 0.25 – 2.5 mm² / 24 – 12 AWG
KLEMMER 5 poler: 2 x sløjfet fase, 2 x sløjfet nul, 1 x mellemleder
SIKRING T2A (fastmonteret)
RADIOPROTOKOL Z-Wave®: EU 868.4MHz – 500 Series
RADIORÆKKEVIDDE 40 m indoor / 80 m outdoor
KAPSLINGSKLASSE IP20
INDMELDING SmartStart Inclusion eller Classic Inclusion
SIKKERHED S2 Security
GODKENDELSER CE
DS/EN 50491-3:2009 or DS/EN IEC 63044-3:2018
DS/EN 60669-2-1, DS/EN60669-2-1/A1, DS/EN 60669-2-1/A12, DS/EN 60669-2-1/AC:2007, DS/EN 60669-1:2018
Z-WAVE CERTIFICERINGSNR. ZC10-19096765
Producent Logic Group
Farve Hvid
Dimensioner DIMENSIONER (HXBXD) 70 (55) mm x 70 (mm) mm x 39 (12) mm
Vægt 0.2000
Strømforbrug 0,6W
Forsyningsspænding 230 Vac
Radiofrekvens 868 MHz
Radio-protokol: Radio protocol Z-Wave®: 868.4MHz – 500 Series – Compliant Z-Wave Plus® SDK 06.51.06
Rækkevidde Op til : 80 meter udendørs / 40 meter indendørs
Maks Udgangseffekt 1 – 200VA / 1 – 250W
Strømforbrug (standby) 0,6W

Indsend din bedømmelse

Kun registrerede brugere kan skrive bedømmelser. Log ind eller registrer